AFM-Holley Terminator X Max Foxbody Kit with AODE/4R70W Transmission Control Gen. 2

Anderson Ford Motorsport has put together all the main components to have a Fox Body specific Terminator X Max kit. This kit was designed for use with the 92-97 Ford AODE or 4R70W electronic automatic transmission swap. Our Anderson kit includes all the necessary wiring, harnesses and components needed to install onto the vehicle. This includes the NEW Anderson Gen 2 specific main harness. This harness has specific OEM Ford connectors to the TPS, MAT, CTS and IAC. No more splicing or using Holley or GM sensors for your Ford. This incorporates the proper power source for the IAC motor built into the harness. We also include the MF Kustoms TFI Ignition harness for a 100% positive connection and proper ground and shielded cable.

Firmware and software downloads are available through Holley.com. Additional options are available above. If you are running a boosted setup, select the external 3 bar MAP sensor. If you wish to utilize the Holley ecu mounting bracket for under the seat (not necessary) then you can select that as an additional option above. AFM has installed and run these kits on several different setups and also can offer support for customers who purchase direct from AFM.

Calibration for your Ford sensors through the Holley software is required. You must change the MAT and CTS to "Ford Modular" for proper scaling. This can be done through the software and laptop tuning or through the handheld sd card (from the software)

PLEASE NOTE! Even though the kit comes with the 3.5" monitor that has some tuning capabilities we advise NOT to use it for main tuning but to either purchase the 558-443 laptop cable for software tuning or create a tune via the SD card and software on your desktop computer. The monitor CANNOT make required changes for Ford IAC's and proper Ford Sensors.

Tech Tip* When creating a file in the software you will need to make sure the ECU has the matching Firmware as the software version you are using, if they do not match the tune file will not properly load into the ecu.

For Off-Road Use ONLY! Not CARB EO approved.

Terminator X main features:

• AFM Foxbody Specific Kits contain - MFK TFI Ignition Adapter - the NEW AFM foxbody specific engine main harness, ECU power and ground harness.
• Includes proper spaced Ford EV1 Injector Harness
• High Impedance Injector Drivers will safely power most Stock injectors, and Holley EFI Injectors. Injector support chart provided in the instructions (Will not control Low Impedance Injectors)
• All of the new Terminator X systems utilize the Bosch LSU 4.9 wideband to relay AFR information to the ECU for accurate reading and precise tuning control.
• Plug and play Transmission Harness for 1992-1997 Ford AODE/4R70W
• Built in 1bar MAP Sensor, - or for Boosted applications, you can disable the internal MAP sensor, and utilize an external MAP Sensor, the harness comes with the connector terminated, making the install simple.
• Plug and play ignition capability with Dual Sync and HyperSpark Distributors, adapter 558-323 required for HyperSpark Distributors.
• 4 Inputs harness – 12v, Ground, 5v, and Frequency, for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake
• Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties
• Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR
• Advanced Tables – 4x 1D Tables, 1x 1D per Gear Table, 4x 2D Tables, 1x 2D per Gear Table, can be used for any custom tables you can dream up, such as Flex Fuel Sensor Offset Table, or a custom fuel or oil pressure safety!
• On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal –Cam Signal. Allow you to identify any Critical engine issues at a glance
• The included 3.5" Touchscreen Handheld contains a calibration wizard, that allows you to quickly build a base tune for any domestic V8 engine. Additionally the handheld provides internal data-logging and a fully customizable gauge display.
• The compact ECU size allows you to mount it virtually anywhere. Remember, diagnostic LEDS must face up!
• Plug and play compatible with more Holley EFI accessories such as; analog style gauges, shift lights, various modules, and coming soon, 12.3" digital dash support!
• Free EFI Tuning Software for complete control of your Terminator X power plant

Installation Requirements*

We recommend moderate / high level wiring and computer skills. Please review the Holley software and do as much research as you can before installation. If you are uncomfortable with learning software and using a laptop then this system should be installed and tuned by a professional shop.