Misc

Synthetic lubricant for V-3 superchargers. This special fluid is required for proper maintenance of the V-3 supercharger. Use of any other fluid will void the warranty and may cause component failure. Fluid Level Checking ProcedureEnsure that the .06"...

PRW Billet Steel Main Girdles are engineered to help eliminate the block flex and cap walk that occurs as a result of stress while under extreme loads, or during nitrous oxide power bursts in high performance engines. PRW main girdles are manufactured...

PRW Billet Steel Main Girdles are engineered to help eliminate the block flex and cap walk that occurs as a result of stress while under extreme loads, or during nitrous oxide power bursts in high performance engines. PRW main girdles are manufactured...

Mustang BBK O2 Wire Harness Extenders. Due to the fact that the O2 sensors are relocated on ALL long tube headers including other manufacturers- These extensions are a must when Installing Full Length Headers on Ford Mustang applications - These BBK O2...

BBK 0-2 Sensor Extension Set (18") for 1986-2009 5.0 MustangBBK O2 Wire Harness Extenders - A must when Installing Full Length Headers - so that the O2 Sensors reach New O2 sensor Locations on the headers. Factory OEM connectors and heat protective...

Reinforced stepped coupler, 2.5"-3"  

This is the complete kit for anyone planning to convert from a carburetor to Atomic EFI. You get the Throttle Body, Power Module (with Wide Band O2 sensor), Handheld Controller, and the Standard Fuel Kit for up to 525hp (at the crank). The throttle body...

If your vehicle already has an electric fuel pump with a return line in place, you might not need to replace it.* If this situation fits your car, consider the Throttle Body Kit which comes with the Throttle Body, Power Module (with Wide Band O2 sensor),...

AF-2989 Braided Stainless Steel Hose Cutting Shears Material: Steel Description: This tool is designed to make clean straight cuts on braided stainless steel hoses. Can also be used on rubber or other braided hoses. This is the best tool you can get...

Reinforced stepped coupler, 3.25"-3.50"

Free up horsepower and replace your worn out smog pump with UPR's New Billet Series Smog Air Pump Eliminator Kit. This kit features a heavy duty high rpm press fit bearing with double seals, stronger support shaft for better bearing support, lighter...

Sick and tired of looking at that broken AC compressor or wanting to just drop some extra pounds from your car then check out UPR's AC Pump Eliminator Kit with holes in pulley. UPR's kit maintains the factory belt length and works with all supercharged...

Remflex exhaust header gasket sets feature 100 percent flexible graphite construction that's effective up to 3,000 degrees F, far exceeding any vehicle's exhaust system temperature. They will rebound 30 percent when tightened, creating an optimum seal...

Mr Gasket Tie-Down Straps, Axle Straps, and Tie-Down Kits are a secure & convenient way to attach your vehicle to the trailer. The ratchet straps are heavy duty high quality products that include zinc plated steel ratchet assemblies with heavy duty...

These Mr. Gasket double ended AN wrenches make it easy to assemble hose ends & maintain your race car or HP vehicle. The contoured edge is comfortable in your hand & the short length helps to prevent over-tightening the hose ends. Each wrench is...

Holley Sniper EFI Self-Tuning kit + handheld EFI monitor- Shiny Finish Base Kit (no pump, filters, fittings, or fuel line) Holley just brought EFI within range! Introducing Sniper EFI! It’s economically priced so you can have all the benefits of...

Holley Sniper EFI Self-Tuning kit + handheld EFI monitor- Black Ceramic Finish Base Kit (no pump, filters, fittings, or fuel line) Holley just brought EFI within range! Introducing Sniper EFI! It’s economically priced so you can have all the...

For 18-19 Mustang GT with MT-82 transmission Is the clutch slipping on your high horsepower 2018-2019 Mustang GT? It may be time to upgrade to a high-performance clutch! This Mcleod RXT twin disc clutch kit is the perfect clutch for your 2018-2019...

Easy to install with one touch lever. PVC suction mount arm adjusts vertically and provides 360 degree rotation. 

Sniper's LED shift light’s compact size allows for endless mounting locations such as above a rearview mirror, on the A-pillar, or right in front on the instrument cluster. Smoked front LED and side display lenses for stealth look when powered off...